Skip to content
SunGeneAgricultural IoT
← All products
Distributed Remote I/O System: Measurement point → Available output → Logger or gateway → Customer system.

Distributed Remote I/O System — connection diagram.

Distributed Remote I/O System

Equipment options & specifications

DIN-rail distributed I/O with separate PROFINET or EtherCAT coupler configurations and expansion modules selected from the project I/O schedule.

Related application hardware: Farm pump & energy monitoring

Farm equipment configurations

Add the right farm signals without replacing every instrument

Use remote I/O where a greenhouse or pump cabinet needs more inputs and outputs. Select the network coupler first, then match each module to the signal and the compatible module bus.

Greenhouse I/O arrangement: a network coupler connects compatible signal modules to the farm controller. Different module buses are selected as separate systems. Connection illustration.
Greenhouse I/O arrangement: a network coupler connects compatible signal modules to the farm controller. Different module buses are selected as separate systems. Connection illustration.

More measurements

Analog and temperature modules collect level, pressure, temperature and other documented signals from the installed transmitters.

More equipment status points

Digital inputs read run, fault, limit-switch and contact states. Match dry contacts, wet contacts, NPN and PNP inputs to the circuit.

More control-panel outputs

Choose relay, transistor or analog output modules to match the receiving equipment. Keep the local protection and interlocks in the control design.

Compare configurations

Open an equipment type to compare its configurations. The quotation identifies the complete device, interfaces and accessories.

Network couplers4 configurations

Modbus TCP coupler

Distributed inputs for an existing Modbus TCP farm controller.

Request this configuration →

Equipment: Dual Ethernet, RS485 and up to 32 compatible bus modules; 24 VDC.

Include with your request: Use the coupler’s matching module bus; IP20 panel installation.

OPC UA server coupler

Expose greenhouse or pump measurements to an OPC UA client.

Request this configuration →

Equipment: OPC UA server, dual Ethernet, RS485 and up to 32 compatible bus modules; 24 VDC.

Include with your request: Client requirements, node mapping and compatible bus modules.

EtherNet/IP coupler

Add field I/O to an existing compatible farm PLC.

Request this configuration →

Equipment: EtherNet/IP slave, dual Ethernet, RS485 and up to 32 compatible bus modules.

Include with your request: PLC network, process-data size and matching module bus.

EtherCAT coupler

Distributed farm equipment I/O on an existing EtherCAT network.

Request this configuration →

Equipment: EtherCAT slave and up to 32 compatible bus modules.

Include with your request: Master compatibility, network topology and matching module bus.

Modules for a compatible coupler8 configurations

8-channel current or voltage input module

Level, pressure and other analog transmitters in one cabinet.

Request this configuration →

Equipment: Separate 0/4–20 mA or 0–5/0–10 V versions; 16-bit inputs.

Include with your request: Select one input version and its compatible coupler.

16- or 32-channel digital input modules

Run, fault and limit-switch contacts across greenhouse equipment.

Request this configuration →

Equipment: Separate low-level, high-level and dry-contact versions.

Include with your request: The selected input circuit and common-terminal wiring.

16- or 32-channel transistor output modules

Control-panel signals for valves and other interface circuits.

Request this configuration →

Equipment: Separate PNP sourcing or NPN sinking versions; up to 200 mA per channel.

Include with your request: Load type, external supply and matching coupler.

8-channel relay output module

Isolated switching contacts for an equipment control panel.

Request this configuration →

Equipment: 8 relays; maximum 2 A per channel; maximum 250 VAC / 30 VDC.

Include with your request: Actual load rating and the local protection circuit.

8-channel current output module

Analog setpoint signals for compatible field equipment.

Request this configuration →

Equipment: 0–20 mA or 4–20 mA output; 16-bit resolution.

Include with your request: Receiving input range and compatible coupler.

8-channel bipolar voltage output module

Analog setpoints for equipment with the corresponding voltage input.

Request this configuration →

Equipment: −5 to +5 V or −10 to +10 V output; 16-bit resolution.

Include with your request: Use the correct voltage-input circuit and compatible coupler.

4-channel PT100/PT1000 input module

Temperature points around crop-storage or greenhouse equipment.

Request this configuration →

Equipment: 3- or 4-wire RTD inputs; PT100 and PT1000 versions.

Include with your request: Sensor type, wire count and compatible coupler.

8-channel NTC input module

Multiple thermistor measurements in one cabinet.

Request this configuration →

Equipment: 8 two-wire NTC inputs; 16-bit resolution.

Include with your request: Thermistor characteristics and compatible coupler.

Standalone temperature modules3 configurations

4-channel Ethernet RTD module

A few temperature points without a large modular rack.

Request this configuration →

Equipment: 4 PT100/PT1000 channels; 2- or 3-wire sensors.

Include with your request: Network protocol, sensor wiring and supply version.

6-channel RTD module

Additional wired temperature measurements.

Request this configuration →

Equipment: 6 PT100/PT1000 channels; 2-, 3- or 4-wire sensors.

Include with your request: Communication interface, sensor wiring and supply version.

8-channel dual-Ethernet RTD module

More temperature points along a wired farm network.

Request this configuration →

Equipment: 8 PT100/PT1000 channels; 2- or 3-wire sensors; dual Ethernet.

Include with your request: Network protocol, sensor wiring and supply version.

Field inputs and sensor connections3 configurations

8-input RS485 field module

Collect contact signals near the field equipment.

Request this configuration →

Equipment: 8 DI, Modbus RTU, 9–36 VDC. Potted cable version: IP67. Tool-free terminal version: IP65.

Include with your request: Choose the enclosure and cable version separately.

4-port M12 sensor distributor

Bring nearby sensor signal cables into one multicore cable.

Request this configuration →

Equipment: 2 signal channels per port; 24 VDC; prefabricated cable version.

Include with your request: NPN/PNP wiring and controller input compatibility; this is a wiring distributor.

8-port M12 sensor distributor

Reduce separate field cable runs around a greenhouse equipment group.

Request this configuration →

Equipment: 1- or 2-channel prefabricated cable versions; 1-channel tool-free terminal version; 24 VDC.

Include with your request: Choose the port, channel and termination version; it is not a network gateway.

Standalone mixed I/O modules7 configurations

2 DI + 2 AI + 2 DO network module

A small group of contacts and transmitters near farm equipment.

Request this configuration →

Equipment: 2 digital inputs, 2 analog inputs and 2 digital outputs; Ethernet module configuration.

Include with your request: Required network protocol, analog ranges and output circuit.

4 DI + 4 DO network module

Read status contacts and provide a few control-panel outputs.

Request this configuration →

Equipment: 4 digital inputs and 4 digital outputs.

Include with your request: Network protocol, contact types, output circuit and power.

Mixed I/O with 2 analog outputs

Connect transmitters and analog setpoints in a farm cabinet.

Request this configuration →

Equipment: 4 DI, 4 AI, 4 DO and 2 AO.

Include with your request: Input/output ranges, network protocol, supply and local control design.

8 DI + 4 DO network module

Collect equipment run/fault contacts and panel outputs.

Request this configuration →

Equipment: 8 digital inputs and 4 digital outputs.

Include with your request: Interface, network protocol, contact types and output loads.

8 DI + 8 DO network module

More contact and output points around a greenhouse equipment group.

Request this configuration →

Equipment: 8 digital inputs and 8 digital outputs.

Include with your request: Interface, network protocol, contact types and output loads.

8 DI + 4 AI + 4 DO network module

Combine hardwired status and analog transmitter measurements.

Request this configuration →

Equipment: 8 digital inputs, 4 analog inputs and 4 digital outputs.

Include with your request: Input ranges, protocol, supply and output circuit.

8 DI + 8 AI + 8 DO network module

A larger mixed-signal equipment group in one farm cabinet.

Request this configuration →

Equipment: 8 digital inputs, 8 analog inputs and 8 digital outputs.

Include with your request: Input ranges, protocol, supply and output circuit.

Standalone analog input modules2 configurations

4-channel network analog input module

Collect four analog farm transmitters.

Request this configuration →

Equipment: 4 AI; 0/4–20 mA or 0–5/0–10 V input configurations.

Include with your request: Select the input ranges, interface, network protocol and power.

8-channel network analog input module

Collect a larger group of level, pressure or other analog signals.

Request this configuration →

Equipment: 8 AI; 0/4–20 mA or 0–5/0–10 V input configurations.

Include with your request: Select the input ranges, interface, network protocol and power.

Standalone digital and relay modules3 configurations

Network digital input modules

Read equipment contacts without a large modular rack.

Request this configuration →

Equipment: Separate 4-, 8- and 16-input network modules.

Include with your request: Contact circuit, protocol, interface and power for the selected version.

Network digital output modules

Provide additional outputs to the farm equipment panel.

Request this configuration →

Equipment: Separate 4-, 8- and 16-output network modules.

Include with your request: Output type, load limits, interface, protocol and local interlocks.

Network output and relay module

Add relay contacts and digital outputs to a farm control cabinet.

Request this configuration →

Equipment: 8 digital outputs and 8 relay channels.

Include with your request: Output circuit, relay loads, network protocol and panel protection.

  • Bus modules, controller expansion boards and standalone network modules are different architectures. Select a complete compatible host or coupler and module set.
  • The existing PROFINET/EtherCAT specifications above describe a separate system. The additional configurations here retain their own supply, coupler and module requirements.

Where this equipment fits

SG-RTU-145: Water Level Telemetry Terminal
Pictured: SG-RTU-145 — Water Level Telemetry Terminal.

Bring existing farm equipment into one record

Connect compatible field signals to the selected collector. Start with the sensors and controller already on site, then agree units, timestamps and the destination for each reading.

Connect remote irrigation and weather points

Farm teams can use the same collection approach for remote irrigation and weather points. The required interfaces, power, network and buffering behavior must match the selected device.

Specifications & version options

Coupler configurations
PROFINET or EtherCAT, selected separately
Expansion families
Switching, analog, PT100, K-type thermocouple and encoder modules
Network ports
2 × RJ45 on the available coupler models
Supply
9-36 VDC on the available coupler models
Assembly
DIN-rail, pluggable module architecture

Equipment quotation

The quotation lists the selected equipment, accessories, price and delivery terms.

Purchasing and delivery details →

Documents and downloads

Selection guidance and application documents. Wiring, register maps and certificates must match the chosen model and version.

Open family selection sheet

English · Web page · printable
Online selection guide

View application guide (PDF)

Application selection guide
PDF · English

Model-specific documents

Tell us which wiring, protocol or calibration documents you need for the equipment.

On this page
Application guide and product-family selection sheet
For your configuration
  • Exact-model datasheet
  • Wiring / pinout
  • Register map, protocol or sample data
  • Model-specific certificates
  • Calibration and measurement evidence
  • Dimensions / installation drawing
Project starter files →
Request an engineering package →
From a product family to your order
  1. Family page

    Compare uses, interfaces and configuration options. These are selection references.

  2. Equipment configuration

    Define the required function, interfaces, power, mounting and accessories for the site.

  3. Written quotation

    Confirm the exact model, configuration, photograph, document revisions, accessories, price, delivery and warranty.

Get selection help

Tell us what you want to measure and where. Send a model number or site photo if you have one.

Text stays in this tab for up to 30 minutes while you browse. Saving across reloads is optional below.

A personal email is welcome.

A country and general site description are enough. If the location is undecided, say so.

Photos, model information or BOM (optional)

Up to 5 files, 10 MB each. PDF, JPG, PNG, WebP, CSV, TXT, DOCX or XLSX.

By submitting this form, you acknowledge the privacy notice.

See where the system fits

Equipment in the system

Example equipment arrangement. Check compatibility and agree who handles software, PLC/SCADA programming and site installation.

Site conditions to check

Compare power, communication and equipment requirements for irrigation, pumps, soil and weather monitoring.

SG-VIB-114: Industrial Accelerometer for Vibration Monitoring

Product photograph

Pictured: SG-VIB-114 — Industrial Accelerometer for Vibration Monitoring.

Continue product selection

Compare related equipment and connection options.

How to choose

  • Create an I/O schedule with each digital, analogue, temperature, encoder and relay point before choosing the coupler and modules.
  • Confirm the controller-side fieldbus, update time, redundancy and diagnostics expected from the remote I/O station.
  • Review the DC field power, module derating, panel width, terminal style, shielding and environmental conditions for each cabinet.

Compatible with

  • PLC or industrial controller using the selected PROFINET or EtherCAT coupler
  • Digital, analog, PT100, K-type thermocouple and encoder expansion modules selected from the I/O schedule
  • Control panels after the ordered coupler supply and grounding path are checked

Typical package

  • One PROFINET or EtherCAT bus coupler for the selected controller network
  • Expansion modules matched line by line to the project I/O schedule
  • DIN-rail power, terminals, shielding and panel wiring selected by the panel builder
  • I/O map, module order and acceptance checklist for the quoted configuration

Applications

SG-RTU-157: Industrial Telemetry Remote Terminal Unit

Product photograph. Pictured: SG-RTU-157 — Industrial Telemetry Remote Terminal Unit.

Use a distributed remote I/O station when field signals need to be collected close to the machine or cabinet and returned to a PLC over industrial Ethernet. Select one controller-side coupler first, then build the station from the actual I/O schedule; PROFINET and EtherCAT are separate configurations rather than simultaneous protocols.

  • Distributed machine I/O returned to a central PLC
  • Cabinet expansion where long home-run signal wiring is impractical
  • Mixed digital, analog, temperature and encoder point collection
See related application hardware

Related selection guides

Related resources

Frequently asked questions

Can one coupler run PROFINET and EtherCAT at the same time?

No. PROFINET and EtherCAT are separate coupler configurations. Select the coupler that matches the PLC network, then build the station from the required I/O modules.

Which I/O module types are available?

This product family includes switching, analog, PT100, K-type thermocouple and encoder expansion modules. Exact channel counts and module order are taken from the project I/O schedule.

Can any I/O module plug into any controller?

No. A bus module needs its matching coupler or controller. Internal expansion boards, bus-mounted modules and standalone Ethernet or RS485 modules use different connection architectures.

What should I send for a remote I/O quotation?

Send the existing controller or coupler, network protocol, number of channels, input and output signal types, sensor wire counts, field supply and cabinet conditions.

Will it work with my existing system?

Use the listed inputs, power and protocol to match the device to your controller. Send its model or an input photo with the equipment request.