Farm equipment selection
Radar or Ultrasonic Level Sensing for Farm Water Tanks?
Compare radar and ultrasonic level instruments for irrigation tanks and farm reservoirs. Check distance, mounting, foam, output and station power before requesting equipment.
Choosing equipment for your farm?
Send your country, measurement points and existing equipment. We can quote an individual device or prepare the sensors, power and data connection for a farm monitoring point.
Hardware in this guide
Product-family illustrations. See each product page for specifications and options.
Plan the connection at your farm
Planning example: compare a covered irrigation tank with an exposed farm reservoir. Send the mounting photos and the highest and lowest water positions so the instrument and its collection interface can be selected together.
- 1
Tank geometry and water surface
- 2
Selected radar or ultrasonic unit
- 3
Matching input and field power
- 4
Water-level record
At your site
Choose the instrument around the water point and the mounting position. Check the empty and full distances, obstructions, foam and changing conditions, then match the documented output and supply to the collector. The model-specific figures below remain part of that selection.
Decision table
Tank or water point
- Radar level sensor
- Review for exposed rivers, reservoirs and tanks with a clear downward view.
- Ultrasonic level sensor
- Review for calm water tanks with a clear acoustic path.
- Guidance
- Share the liquid, tank drawing and photos taken from the mounting point.
Distance and highest fill
- Radar level sensor
- The listed water-level unit measures 0.1–65 m.
- Ultrasonic level sensor
- Select a 5, 10, 15, 20 or 30 m version; its blind zone depends on that version.
- Guidance
- Check sensor-to-water distance at both empty and full conditions. Keep the highest level outside the selected blind zone.
Foam and changing conditions
- Radar level sensor
- Avoids sound-speed changes in the air path, but dense foam or weak reflections can still cause a poor reading.
- Ultrasonic level sensor
- Foam, steam and strong temperature gradients can weaken or distort the acoustic echo.
- Guidance
- Describe the worst operating condition. A radar label alone does not establish reliable measurement through foam.
Show the remaining comparison criteria
Equipment in the system
Example equipment arrangement. Check compatibility and agree who handles software, PLC/SCADA programming and site installation.
Field equipment options
Compare the measurements and accessories for this site. Confirm each selected signal, electrical interface and connection to the acquisition device.
See other field equipment (1)
Matching data collection device
Confirm whether the selected outputs need a PLC, RTU, logger or gateway. Match the inputs, power and destination protocol before quotation.
Data destination
Customer platform or an agreed third-party service
Turn the tank details into an equipment choice
Tank suppliers, irrigation teams and facility operators can start with a drawing and a few site photos. These checks help avoid a sensor that fits the range but cannot be mounted or connected.
Show the measurement point
Mark the sensor position, tank shape, inlet, internal pipes and the lowest and highest water levels. Include the opening size and the distance from the sensor face to the water at each limit.
Define the reading
Agree whether the system needs distance, water depth, percentage full or volume. Record the reference point and units. A volume display also needs the tank geometry or a level-to-volume table.
Check the complete connection
List the sensor output, power supply, controller input, cable, mounting parts and remote data path. Compare this installed equipment scope when requesting prices for the two methods.
Check readings before rollout
Compare local and remote values at agreed fill levels, including filling and any expected foam. Check loss-of-signal handling and high/low alerts. Agree any independent overflow protection separately.

Application illustration. Tank dimensions, sensor mounting and service access help determine the level measurement.
Show the sensor view at the farm tank
Show the tank, sensor mounting position and highest and lowest water levels. Include the output and power required by the receiving equipment.
Request farm equipmentChoose Radar level sensor when
- An exposed water point has changing air conditions and a clear view of the surface
- The required distance fits the listed 0.1–65 m water-level unit
- A compatible RS485 Modbus input and 10–33 VDC supply are available
Choose Ultrasonic level sensor when
- A calm water surface provides an unobstructed acoustic path
- The mounting opening and highest fill leave the selected version’s blind zone clear
- The selected 4–20 mA or RS485 output fits the existing controller
Information needed for quotation
- Tank or reservoir dimensions and photos
- Sensor-to-water distances at lowest and highest fill
- Foam, inlet and mounting conditions
- Existing controller input and available power

Application illustration. Mark the measurement points, power and cable routes on a farm layout for an equipment request.
Send the mounting details with the request
Mark the measurement points, field power and receiving system on a farm layout. Include equipment already in use and the number of points to be added.
Request farm equipmentOfficial technical references
- VEGA: radar and ultrasonic measurement principles
Background on signal paths, vessel geometry and process conditions. Sensor-specific performance must be checked for the selected model.
- WIKA: non-contact radar uses and limitations
Explains why liquid properties, dense foam and tank obstructions remain part of radar selection.
Related pages
FAQ
What should I send for a farm tank-level quotation?
Send the tank or reservoir dimensions, mounting photos, empty and full distances, water-surface conditions, available power and the controller or logger input. Add the reporting destination and required point count.
Does radar always work through foam?
No. Foam can reduce the returned signal for both radar and ultrasonic sensing. Share its thickness, density and when it appears. Check the selected sensor under those conditions; hydrostatic or another measurement method may suit the site better.
Can the radar unit replace a 4–20 mA sensor directly?
The listed radar water-level unit provides RS485 Modbus RTU. An existing analog-only controller needs a compatible input path or a different selected sensor. Confirm the controller model and wiring before choosing a replacement.
Which option can use a 12 VDC supply?
The listed radar unit accepts 10–33 VDC. In the ultrasonic family, 12 VDC is available on the RS485 configuration only; other supply options are 24 VDC or 220 VAC. Confirm the output and power combination for the ordered version.
Is tank height enough to select the measuring range?
Also measure the distance from the sensor face to the water at the lowest and highest fill. The longest distance must fit the selected range, and the shortest must remain outside its blind zone. Send the mounting opening and nearby obstructions with those dimensions.
Does an IP68 sensor make the whole tank station IP68?
The rating applies to the specified part. The listed radar unit is IP68; the ultrasonic probe is IP68 and its display unit is IP66. Connectors, cable entries, power equipment and any cabinet need their own installation and protection checks.
Do I need a separate gateway for remote tank readings?
These level sensors supply wired RS485 or selected analog outputs. Remote monitoring also needs a matching input device, a suitable 4G, LoRaWAN or Ethernet connection, and a receiving system. A LoRaWAN gateway alone does not read a wired sensor; a compatible sensor node is needed.
What should I send for an equipment quotation?
Send the country, measurements, equipment already on site, available power and the system receiving the data. Add a site sketch or instrument photo and the approximate point count.
Can I buy individual devices or request a complete farm monitoring point?
Yes. A device request can cover a missing measurement or connection. A complete point brings together the instruments, matching inputs, power, enclosure and agreed data connection, with local installation responsibilities set out in the proposal.
What should be checked before adding more farm sites?
Compare the field readings with the records received by the platform. Check units, timestamps, interruptions and recovery, then record the equipment configuration and the team responsible for service.


